Showing posts with label Alternate Energy. Show all posts
Showing posts with label Alternate Energy. Show all posts

Tuesday, 15 September 2009

Energy Efficient Homes

Energy efficient homes are homes where the thermal losses (or gains in the case of air conditioning) of comfort conditioning have been minimized. Energy Efficient Homes can be identified only if a properly qualified specialist carries out an energy audit or a BER analysis.

Whether you want to retrofit the existing energy consuming equipment or implement upgrades a long term investment approach will benefit you over years to come.

How to make your home energy efficient

There are several aspects in your home that you will have to look into if you were to make your home energy efficient.

  • Add insulation to your home -For this you will have to find where insulation has to be improved. An analysis has to follow (preferably using suitable software) to determine the cost effective additional thickness required at various weak spots.

A comparison of various insulations and also the estimated payback period on the investment is a must. Adequately insulating heating Ducts (especially when running through unheated areas) along with their leak sealing, insulating water tanks, plumbing and electric water heaters is also a part of the job.

  • Upgrade your Heating System -The equipment must compulsorily carry a green energy rating in the upper part of the scale. Know when your boilers and controls are due for a replacement. If your boiler is over 15 years old or in poor condition needing frequent repairs and your fuel bills are too high the time may be ripe for a replacement. Find out what is the best suited fuel for your heating system. Points to consider in this regard are;
    • The cost and the availability (keeping in mind what is cheap today may not be cheap tomorrow).
    • The type of equipment used to convert fuel to heat energy and its distribution over the building.
    • The cost of purchase, installation and maintenance (perhaps for another 15 years or so).
    • The efficiency of the Boilers and the distribution system
    • Any environmental impact of the fuel itself or its products of combustion.
    • See whether use of Geothermal Energy, Heat pumps, solar thermal and other sustainable heat sources is more advantageous for your home
  • Install More efficient Controls – Today's programmable thermostats and Timers afford you a big advantage to conserve energy. A degree difference in your room setting will save you considerable energy without even your feeling the difference. The terminal equipment etc. if fitted with more precise TRVs will empower you with better control over your energy usage.
  • Windows and Doors improvement- Consider installing interior and exterior Storm Windows because it might save 25% to 50% of heat lost through the windows. It will further improve if Low-e type double glazed windows are fitted. Design, Selection and Installation of windows play a big part in your efforts to save energy. Consulting a specialist therefore is a must.
  • Use Alternative Energy appliances- Use of solar thermal panels (for heating and hot water), Use of geothermal energy, use of waste heat (eg. in CHPs) may be very cost effective in certain situations and where these resources are available a plenty. It is advisable to seek expert advise to find out how practical these for your specific requirement.
  • Landscaping for energy efficiency- Depending on the geographic location of your house landscaping strategies may be effectively employed to conserve home energy. Some of these may be ;
    • Maximize the Sun's direct heating effect in the winter
    • Maximize the shade in the hot summer
    • Deflecting the cold winter breeze away from the building
    • Direct summer warm breeze towards the building
    • Use wind breaks of trees and shrubs to reduce wind chill in the winte
  • Use energy efficient Lighting- Use of CFL, LED (SSL) and Solar Powered Lights are highly encouraged these days. The use of Day lighting is another measure that can be considered.

For further information you can contact Eon Solar who will advise you or guide you to their best qualified associate for your requirement.

Green Energy Have You Considered Making The Alternate Energy Change?

My first suggestion would be to start slow. Start small with everyday things like sharing rides to work, walking or riding your bike to lower how much fuel you are consuming and lower your contribution to air pollution. Change the light bulbs in your home to the smaller fluorescent bulbs. Regular light bulbs can really increase your monthly bills and the newer ones will last a lot longer. This adds up to big savings for you over time.

Another approach is to do a little maintenance around the house. Start caulking any gaps around the doors and windows and seal up any opening. This will help keep out drafts that cost you money. Another big tip is if you want to spend a little money - insulate, insulate, insulate! You will always make your money back on insulation. Having a well insulated home cuts down on those high energy cost in the wintertime. The more insulation, the less your furnace or heater will turn off and on costing you less.

One thing I hadn’t thought much about before was my appliances until my washer started to go crazy. If you have older appliances, they are probably eating your lunch in energy. It’s true! I couldn’t believe how much difference there was just in the ten years difference since I had bought my old one. You will actually save enough on your monthly bills over time to pay for a new energy efficient appliance. So if your spouse has been complaining about that old frig or washer, surprise them and replace it for them and save some money.

Of course, one of the most obvious “Going Green” changes that most of us have been exposed to since we were young is recycling. The bonus is that many vendors and manufacturers are making it easy for us. Watch for the recycling emblem when purchasing products. Buy more than one trash can so that you can separate out your paper, metal, glass and plastic.

These are all excellent ideas that you can utilize to start your “Going Green” lifestyle. Should you decide to pursue even bigger ideas’ there are many resources and a large amount of information available.

Wednesday, 26 August 2009

Solar Energy Source

Did you know that in 15 minutes the sun radiates as much energy as mankind consumes in all forms, during an entire year? Did you know that in one day the sun radiates enough energy on the United States to power the entire nation for a year and a half? Not only that, but it does it every day - for free. Solar power is a safe, clean and renewable energy resource that will no doubt play a vital role in powering our future.

How can the energy from the sun be harnessed? And how can we put that energy to practical use? Harnessing the sun’s power is accomplished through the use of a photovoltaic system. Basically, the word “photovoltaic” is used to describe a device, which when exposed to the sun’s radiation, creates electrical power. It’s abbreviated as “PV”. PV systems incorporate the use of PV modules, (which are also commonly referred to as “solar panels”), to generate energy from sunlight and inverters which convert that power and safely deliver it to the utility grid for our use.

When properly designed, a PV system not only helps our environment, but it makes economical sense as well. Owners of PV systems make an important contribution to protecting our environment while enjoying the economic advantages of their “clean” electricity at the same time.

In the following sections you will learn more about how to plan your own PV system and why the inverter is such an important component.

The sun - a Reliable Source of Energy

The United States is well suited for the use of solar power. Most of the nation is exposed to high levels of irradiation every day. Even in parts of the nation confronted with rainy summers and dark winter months, solar power can still be put to use economically.

Depending on the location, the average annual amount of energy PV modules will be exposed to totals between 950 to 2,150 kilowatt hours per square meter (kWh/m2). This is a lot considering that 1,000 kWh/m2 is equal to the energy of about 25 gallons of heating oil. So you can see that the energy potential is already there and PV systems are an excellent way to put it to work for you.

Ample Sun throughout the Nation

The sunlight that your solar system is exposed to is sometimes “direct” or unobstructed by clouds. At other times the sunlight is “diffused”, that is, filtered to some degree either by clouds or the atmosphere in the more northern parts of the country. Solar technology can utilize either form of sunlight. The seasons, elevation and angle of the sun also affect the usable amount of energy. In the northwest for example, the amount of diffused sunlight caused by clouds is relatively high. However, even diffused sunlight can be effectively harnessed to produce electricity by using a well-designed photovoltaic system.

PV Modules – the Cooler the Better

It seems counterintuitive because PV modules are made to be mounted in the sun, but the fact is that they perform better when cooler – in fact, the ideal temperature is right around 25°C.

This means that PV systems up in the clear air and cool temperatures of the mountains will perform better than a system of the same size located in the desert. The amount of direct sunlight at the equator for example, is much higher than in the latitudes in North America; however, the high ambient temperatures heat the modules up and therefore reduce the overall system performance considerably. The power loss is approximately 0.4 % per °C for common PV modules.

So although the sunlight is weaker in North America as compared to South America, the temperatures are cooler making the PV modules more efficient. This compensates for the lower intensity of the sun.

Types of Solar Systems

The sun delivers its energy in two forms: heat and light.

Solar systems can efficiently convert either form into power for practical use.

When many people hear the term “solar system” they think of solar hot water, where the sun is used to heat water for swimming pools or domestic use. This is accomplished by exposing the water to the sun’s heat prior to using it. We also make use of the sun’s heat by orienting windows towards the south (in the northern hemisphere) to take advantage of the sun’s warmth in the winter. This is called “passive” solar. This term is used to describe methods of using the sun’s energy indirectly, such as through bio-mass or heat pumps.

The term solar power system on the other hand, typically describes only those systems that convert sunlight into heat (solar thermal energy) or electricity (photovoltaics). Photovoltaics and solar thermal energy are not in direct competition - quite the contrary: they ideally complement each other and can be combined well. Many specialized companies provide innovative solutions for this purpose.

How Photovoltaics Work

As solar power becomes increasingly popular, more and more solar panels can be seen on the roofs of homes and businesses alike. These solar panels employ one of the most environmentally friendly methods for producing electricity: “photovoltaic”. The term photovoltaic, or PV, is used to describe something that creates electricity when exposed to sunlight. Solar panels, or PV modules, are made up of several solar cells. Each cell is comprised of materials which have photovoltaic properties.

Photovoltaic technology is actually quite simple:

Electricity can be produced by solar cells whose principal component consists of a semiconductor that is typically made of silicon. A semiconductor consists of a material that cannot be classified as an isolator or a conductor and whose electrical properties can be influenced by adding foreign substances (doping). The solar cells comprise two adjoining semiconductor layers that are equipped with separate metal contacts and have each been doped, thus creating an “n” layer (n = negative) with a surplus of electrons and below that, a “p” layer (p = positive) with an electron deficiency. Due to the difference in concentration, the electrons flow from n into the p area, thus creating an electrical field, or “space charge zone”, inside the semiconductor structure.

The Photovoltaic Effect

The upper “n” layer in a solar cell is so thin that the photons from sunlight can penetrate it and can only discharge their energy to an electron once they are in the space charge zone. The electron that is activated in this manner follows the internal electrical field and thus travels outside of the space charge zone and reaches the metal contacts of the “p” layer. When an electrical load is connected, the power circuit is closed: the electrons flow across the electrical load to the solar cell’s rear contact and then back to the space charge zone. This effect is called the “photovoltaic effect” (derived from ‘‘Phos’’, the Greek word for light and the name of the physicist Alessandro Volta). An inverter, the “heart” of the system, converts the direct current (DC) produced by the solar cells into alternating current (AC).

From the Cells to the Module

The sun radiates approximately 1000W per square meter, so a 10 x 10 cm solar cell is exposed to nearly 10 watts of radiated power. Depending on the quality of the cell, it can produce an electrical output of 1 - 1.5 watts. To increase the output, several cells are combined and connected to a PV module. The connection of several PV modules is also referred to as a PV array. You can learn more about photovoltaics using the menu bar on the upper right-hand side.

How Solar Thermal Energy Works

Solar thermal energy is the use of solar energy to produce heat.

This is an effect you’re familiar with if you’ve ever gotten into your car after it has been parked in the sun on a hot summer day. Solar thermal energy works in the same way except that the heat generated is put to practical use to heat water or space heating.

In addition, by using a solar thermal system, you make an effective contribution in preserving our energy reserves and environmental protection by reducing CO2 emissions.

A Simple Principle that Integrates Easily

The solar collectors absorb the sun’s rays, convert them to heat and transfer the heat to a heat-transfer fluid. (The heat-transfer fluid is typically a glycol and water mixture in regions where seasonal freezing in a concern.) The heat-transfer fluid is then pumped into a heat exchanger located inside the water storage tank where it heats the water.

After releasing its heat via the heat exchanger, the heat-transfer fluid flows back to the collectors to be reheated. The controller keeps the heat-transfer fluid circulating whenever there is heat available in the solar collectors. In the winter, a boiler serves as an alternate heat source. Solar thermal systems can be integrated into existing hot water systems with relative ease.

Other Renewable Energy Sources

Many nations count on coal, oil and natural gas to supply most of their energy needs, but reliance on fossil fuels presents a big problem. Fossil fuels are a finite resource. Eventually, the world will run out of fossil fuels, or it will become too expensive to retrieve those that remain. Fossil fuels also cause air, water and soil pollution, and produce greenhouse gases that contribute to global warming.

Renewable energy resources, such as wind, solar and hydropower, offer clean alternatives to fossil fuels. They produce little or no pollution or greenhouse gases, and they will never run out.

Wind Power

Wind power is actually a form of solar power, because wind is caused by heat from the sun. Solar radiation heats every part of the Earth’s surface, but not evenly or at the same speed. Different surfaces—sand, water, stone and various types of soil-absorb, retain, reflect and release heat at different rates, and the Earth generally gets warmer during daylight hours and cooler at night.

As a result, the air above the Earth’s surface also warms and cools at different rates. Hot air rises, reducing the atmospheric pressure near the Earth’s surface, which draws in cooler air to replace it. That movement of air is what we call wind.

When air moves, causing wind, it has kinetic energy-the energy created whenever mass is in motion. With the right technology, the wind’s kinetic energy can be captured and converted to other forms of energy such as electricity or mechanical power. That’s wind power.

Just as the earliest windmills in Persia, China and Europe used wind power to pump water or grind grain, today’s utility-connected wind turbines and multi-turbine wind farms use wind power to generate clean, renewable energy to power homes and businesses.

Wind power should be considered an important component of any long-term energy strategy, because wind power generation uses a natural and virtually inexhaustible source of power—the wind—to produce electricity. That is a stark contrast to traditional power plants that rely on fossil fuels.

And wind power generation is clean; it doesn’t cause air, soil or water pollution. That’s an important difference between wind power and some other renewable energy sources, such as nuclear power, which produces a vast amount of hard-to-manage waste.

One obstacle to increasing worldwide use of wind power is that wind farms must be located on large tracts of land or along coastlines to capture the greatest wind movement.

Devoting those areas to wind power generation sometimes conflicts with other priorities, such as agriculture, urban development, or waterfront views from expensive homes in prime locations.

As the need for clean, renewable energy increases, and the world more urgently seeks alternatives to finite supplies of oil, coal and natural gas, priorities will change.

And as the cost of wind power continues to decline, due to technology improvements and better generation techniques, wind power will become increasingly feasible as a major source of electricity and mechanical power.

Hydropower

Water flowing downstream is a powerful force. Water is a renewable resource, constantly recharged by the global cycle of evaporation and precipitation. The heat of the sun causes water in lakes and oceans to evaporate and form clouds. The water then falls back to Earth as rain or snow, and drains into rivers and streams that flow back to the ocean. Flowing water can be used to power water wheels that drive mechanical processes. And captured by turbines and generators, like those housed at many dams around the world, the energy of flowing water can be used to generate electricity.

Biomass Energy

Biomass has been an important source of energy ever since people first began burning wood to cook food and warm themselves against the winter chill. Wood is still the most common source of biomass energy, but other sources of biomass energy include food crops, grasses and other plants, agricultural and forestry waste and residue, organic components from municipal and industrial wastes, even methane gas harvested from community landfills. Biomass can be used to produce electricity and as fuel for transportation, or to manufacture products that would otherwise require the use of non-renewable fossil fuels.

Hydrogen

The jury is still out on whether hydrogen will ultimately be our environmental saviour, replacing the fossil fuels responsible for global warming and various nagging forms of pollution. Two main hurdles stand in the way of mass production and widespread consumer adoption of hydrogen “fuel-cell” vehicles: the still high cost of producing fuel cells; and the lack of a hydrogen refuelling network.

Reining in manufacturing costs of fuel-cell vehicles is the first major issue the automakers are addressing. While several have fuel-cell prototype vehicles on the road—Toyota and Honda are even leasing them to the public in Japan and California—they are spending upwards of $1 million to produce each one due to the advanced technology involved and low production runs. Toyota hopes to reduce its costs per fuel-cell vehicle to around $50,000 by 2015, which would make such cars economically viable in the marketplace. On this side of the Pacific, General Motors plans to sell hydrogen-powered vehicles in the United States by 2010.

Another problem is the lack of hydrogen refuelling stations. Major oil companies have been loath to set up hydrogen tanks at existing gas stations for many reasons, ranging from safety to cost to lack of demand. But obviously the oil companies are also trying to keep customers interested in their highly profitable bread-and-butter product: gasoline. A more likely scenario is what is emerging in California, where some 38 independent hydrogen fuel stations are located around the state as part of a network created by the non-profit California Fuel Cell Partnership, a consortium of automakers, state and federal agencies, and other parties interested in furthering hydrogen fuel-cell technologies.

The benefits of ditching fossil fuels for hydrogen are many, of course. Burning fossil fuels like coal, natural gas and oil to heat and cool our buildings and run our vehicles takes a heavy toll on the environment, contributing significantly to both local problems such as elevated particulate levels and global ones such as a warming climate. The only by-product of running a hydrogen-powered fuel cell is oxygen and a trickle of water, neither of which will cause any harm to human health or the environment.

But right now, 95 percent of the hydrogen available in the United States is either extracted from fossil fuels or made using electrolytic processes powered by fossil fuels, thus negating any real emissions savings or reduction in fossil-fuel usage. Only if renewable energy sources-solar, wind and others-can be harnessed to provide the energy to process hydrogen fuel can the dream of a truly clean hydrogen fuel be realized.

Stanford University researchers in 2005 assessed the environmental effects of three different hydrogen sources: coal, natural gas, and water electrolysis powered by wind. They concluded that we’d lower greenhouse gas emissions more by driving gasoline/electric hybrid cars than by driving fuel-cell cars run on hydrogen from coal. Hydrogen made using natural gas would fare a little bit better in terms of pollution output, while making it from wind power would be a slam-dunk for the environment.

Geothermal Energy

The heat inside the Earth produces steam and hot water that can be used to power generators and produce electricity, or for other applications such as home heating and power generation for industry. Geothermal energy can be drawn from deep underground reservoirs by drilling or from other geothermal reservoirs closer to the surface.

Ocean

As any board or body surfer will tell you, the ocean’s tidal currents pack considerable wallop. So why wouldn’t it make sense to harness all that formidable ocean power-which is not unlike that of the rivers that drive hydropower dams or the wind that drives wind turbines-to make energy?

The concept is simple, says John Lienhard, a University of Houston mechanical engineering professor: “Every day the moon’s gravitational pull lifts countless tons of water up into, say, the East River or the Bay of Fundy. When that water flows back out to sea, its energy dissipates and, if we don’t use it, it’s simply spent.”

According to Energy Quest, an educational website of the California Energy Commission, the sea can be harnessed for energy in three basic ways: using wave power, using tidal power, and using ocean water temperature variations in a process called “ocean thermal energy conversion”.

  • In harnessing wave power, the back-and-forth or up-and-down movement of waves can be captured, for example, to force air in and out of a chamber to drive a piston or spin a turbine that can power a generator. Some systems in operation now power small lighthouses and warning buoys.
  • Harnessing tidal energy, on the other hand, involves trapping water at high tide and then capturing its energy as it rushes out and drops in its change to low tide. This is similar to the way water makes hydroelectric dams work. Already some large installations in Canada and France generate enough electricity to power thousands of homes.
  • An OTEC system uses temperature differences between deep and surface waters to extract energy from the flow of heat between the two. An experimental station in Hawaii hopes to develop the technology and someday produce large amounts of electricity on par with the cost of conventional power technologies.

Proponents say that ocean energy is preferable to wind because tides are constant and predictable and that water’s natural density requires fewer turbines than are needed to produce the same amount of wind power. Given the difficulty and cost of building tidal arrays at sea and getting the energy back to land, however, ocean technologies are still young and mostly experimental. But as the industry matures, costs will drop and some analysts think the ocean could power nearly two percent of U.S. energy needs.

Tidal energy pioneers are also hard at work on the U.S. Atlantic coast. The New Hampshire Tidal Energy Company is developing tidal power in the Piscataqua River between New Hampshire and Maine.

Thursday, 6 August 2009

Solar Energy Advantages Disadvantages

Solar Energy Advantages

Saves you money

  • After the initial investment has been recovered, the energy from the sun is practically FREE.
  • The recovery/ payback period for this investment can be very short depending on how much electricity your household uses.
  • Financial incentives are available from the government that will reduce your cost.
  • If your system produces more energy than you use, your utility company can buy it from you, building up a credit on your account!
  • It will save you money on your electricity bill if you have one at all.
  • Solar energy does not require any fuel.
  • It's not affected by the supply and demand of fuel and is therefore not subjected to the ever-increasing price of gasoline.
  • The savings are immediate and for many years to come.
  • The use of solar energy indirectly reduces health costs.

Environmentally friendly

  • Solar Energy is clean, renewable (unlike gas, oil and coal) and sustainable, helping to protect our environment.
  • It does not pollute our air by releasing carbon dioxide, nitrogen oxide, sulphur dioxide or mercury into the atmosphere like many traditional forms of electrical generation does.
  • Therefore Solar Energy does not contribute to global warming, acid rain or smog.
  • It actively contributes to the decrease of harmful green house gas emissions.
  • It's generated where it is needed.
  • By not using any fuel, Solar Energy does not contribute to the cost and problems of the recovery and transportation of fuel or the storage of radioactive waste.

Independent/ semi-independent

  • Solar Energy can be utilized to offset utility-supplied energy consumption. It does not only reduce your electricity bill, but will also continue to supply your home/ business with electricity in the event of a power outage.
  • A Solar Energy system can operate entirely independently, not requiring a connection to a power or gas grid at all. Systems can therefore be installed in remote locations (like holiday log cabins), making it more practical and cost-effective than the supply of utility electricity to a new site.
  • The use of Solar Energy reduces our dependence on foreign and/or centralized sources of energy, influenced by natural disasters or international events and so contributes to a sustainable future.
  • Solar Energy supports local job and wealth creation, fuelling local economies.

Low/ no maintenance

  • Solar Energy systems are virtually maintenance free and will last for decades.
  • Once installed, there are no recurring costs.
  • They operate silently, have no moving parts, do not release offensive smells and do not require you to add any fuel.
  • More solar panels can easily be added in the future when your family's needs grow

Solar Energy Disadvantages

  • The initial cost is the main disadvantage of installing a solar energy system, largely because of the high cost of the semi-conducting materials used in building one.
  • The cost of solar energy is also high compared to non-renewable utility-supplied electricity. As energy shortages are becoming more common, solar energy is becoming more price-competitive.
  • Solar panels require quite a large area for installation to achieve a good level of efficiency.
  • The efficiency of the system also relies on the location of the sun, although this problem can be overcome with the installation of certain components.
  • The production of solar energy is influenced by the presence of clouds or pollution in the air.
  • Similarly, no solar energy will be produced during night time although a battery backup system and/or net metering will solve this problem.
  • As far as solar powered cars go - their slower speed might not appeal to everyone caught up in today's rat race.

How Solar Energy Panels Work

You've heard the buzz about alternative energy sources but have you ever wondered how solar energy panels work? Of course, if you want to install a system for your home, you want to understand something about how you'll get energy from the sun and how it can benefit you.

You've probably used a solar powered calculator for doing mathematic problems. You know the kind; as long as the calculator is exposed to light, it operates perfectly. Did you know that there are portable solar energy panels that you could use to operate a laptop computer, a radio or CD player, a cell phone, digital camera or other small appliance when camping, hiking or even when sitting beside your swimming pool? These small, flexible solar energy panels roll up for storage in a small space and simply unroll for placement in the bright sunshine when you want a little power to run a small electric device. These solar panels function pretty much the same as a large roof-top solar collector panel.

These solar collection cells, whether large or small, are called photovoltaic cells. Photovoltaic, when broken down, is easy to understand. "Photo" means light and "voltaic" means electric; the word means electricity from light. These devices were invented to power satellites and devices in space but now are in use all over the world in households.

Solar energy panels, also called photovoltaic (PV) panels, are made of material that concentrate the sun's rays. When the sun's rays strike a PV panel, some of the energy can be absorbed by the panel. This can be used to heat water passing through pipes in the solar energy panel. It can be absorbed by semiconductor material and used to generate electricity.

When PV cells collect electrons from the light being absorbed, these electrons flow in a single direction because of the electric fields they contain. The flow of electrons is controlled by the use of metal contacts at the top and bottom of the solar energy panel so that current can be extracted for use. This can power the small appliance or used to power an entire house.

Using solar energy panels for collecting the sun's power for home use can be quite simple. They usually consist of a black metal or wooden box that is designed to be the right size for placement on the roof of the house where it will be installed. The box is well insulated and is always black on the inside to help focus the sun's energy and absorb it most efficiently. Inside the box may be semiconductor material or piping.

If hot water is being generated, the box will contain zigzag patterns of copper piping through which the water will pass, becoming hot from the energy of the sun. If the solar energy panel is used in this way, the heated water will then pass into a storage tank which is very well insulated and may be created from an altered traditional hot water heating tank. The water is then used when required by simply turning on a water tap in the bathtub, sink or when the hot water valve opens when operating the washer or dishwasher. The occupants of the home never realize the hot water is not being heating in a traditional manner using electricity or gas from the utility company. A carefully designed system can provide enough hot water for any family's needs.

If the solar energy panel is used to create electricity, the current is stored inside the home in batteries somewhat like the one you've seen in your car. Usually there is a bank of several batteries that store the electricity. A control unit makes sure the right amount of voltage and amperage goes into the electric wires when someone turns on a light switch, when the home's heat or air conditioning comes on, or other demand is placed on the batteries to supply their stored electric power to the house.

Of course, it is a bit more complex if you get into all the engineering details. This is, however, a basic explanation of how solar energy panels can provide for your energy needs.